العربية Get a quote

Technical guides

Why an ANFO loading hose must be anti-static: static, stray current and safe charging

When ANFO prill is blown through a hose into a blast hole, friction between the moving prill and the hose wall generates static electricity. A loading hose made for ANFO is designed to let that charge drain away in a controlled way, while not becoming an easy path for stray current into the blasting circuit.

By the Six Winds engineering team · Updated

Quick answer

Use a hose made for ANFO loading (anti-static, also called conductive or semi-conductive), connect the loader to earth as your blasting procedure requires, and never substitute an ordinary air or water hose. An ordinary plastic hose lets static build up close to the explosive and the detonators.

Step by step

  1. Use a hose made for ANFO loadingCheck the hose is sold for pneumatic ANFO charging and has its datasheet and test certificate. Our ANFO loading hose has an anti-static compound and a continuous orange stripe so it is easy to recognise on site.
  2. Earth the loaderThe hose drains static to the loader, so the loader itself must be connected to earth in the way your blasting procedure sets out. A conductive hose on an unearthed loader gives no protection.
  3. Keep the circuit apart from stray currentFollow the mine procedure for stray-current checks before charging, especially near electrical equipment, pumps, rails and power cables.
  4. Inspect before every shiftCuts, flat spots and wear down to the inner layer change how the hose behaves electrically. Replace a damaged hose; do not tape it.
  5. Record and re-testKeep the hose certificate with the loader records and re-test or replace the hose at the intervals your procedure and the maker give.

How static builds up during pneumatic charging

In pneumatic charging, compressed air carries ANFO prill at speed from the loader vessel through the hose into the hole. Every grain rubs against the hose wall. That rubbing separates electric charge, in the same way as walking across a carpet, and the charge collects on the hose and in the prill stream.

If the charge has nowhere to go it can build up until it discharges as a spark. In a hole that holds explosive and detonator leads, an uncontrolled discharge is a recognised hazard, which is why mine and quarry blasting procedures specify the type of hose that may be used.

What an anti-static loading hose does

An ANFO loading hose is made from a compound that conducts electricity just enough to let static drain along the hose to the loader and from there to earth. Our hose uses an anti-static (conductive) thermoplastic compound for exactly this purpose.

The same hose must not conduct so well that it becomes a good path for stray currents (from electrical equipment, leaking cables or rails) into the hole and the blasting circuit. A loading hose is therefore designed for a controlled range of resistance: high enough to resist stray current, low enough to bleed off static. The maker states the range on the test certificate, and your procedure tells you how to check it.

Why an ordinary air or water hose is not acceptable

  • It insulates: standard PVC or rubber air hose does not let static drain, so the charge stays on the hose and in the prill.
  • It is not marked: on a busy face it is easy to pick up the wrong hose. A loading hose with a continuous coloured stripe, such as the orange stripe on ours, is recognised at a glance under cap lamps.
  • It is not certified: without a datasheet and test certificate there is no evidence for the safety file or the client's audit.

Earthing the loader

The anti-static hose only works if the charge has somewhere to go. The loader (or charging unit) is connected to earth as the blasting procedure requires, and the hose is connected to the loader outlet with a fitting that keeps the electrical path continuous. Check the earth connection at the start of each shift, not only when the loader is commissioned.

Other features that matter underground

  • Self-extinguishing: the hose material does not keep burning once a flame is removed.
  • Abrasion resistant: smooth inner and outer surfaces stand up to prill flow and dragging over rock.
  • Flexible but firm: it bends for handling and coiling, yet is stiff enough to push up into steep and upward holes.
  • Temperature: made for use from -35 °C to +65 °C, which covers summer surface work in Saudi Arabia and cooler underground areas.

What to send us for a quotation

The bore size (or your loader make and model), the length per coil, the number of coils, the delivery site, and whether you need a certificate of origin or test certificate with the shipment. See the ANFO explosive loading hose page for sizes and the datasheet, or e-mail sales@sixwinds.com.sa.

Common questions

Is an ANFO loading hose the same as a conductive hose?

It is a hose designed to dissipate static in a controlled way, often described as anti-static, conductive or semi-conductive. What matters is that it is made and certified for pneumatic ANFO charging, not the name.

Can I use a normal air hose for ANFO in an emergency?

No. An ordinary air hose lets static build up close to the explosive and the detonators. Stop charging until the correct loading hose is available.

Does the hose replace earthing the loader?

No. The hose drains the charge to the loader; the loader must be earthed as your blasting procedure requires, otherwise the charge has nowhere to go.

How do I know the hose is still safe?

Inspect it before every shift for cuts, flat spots and wear, and re-test or replace it as your procedure and the maker require. A worn hose cannot be relied on electrically.

Do you have ANFO loading hose in stock in Saudi Arabia?

Yes. We hold the anti-static ANFO loading hose in Jeddah in 16, 19, 25 and 32 mm bore and deliver to mine sites across the Kingdom.

Need these items? E-mail your list or a nameplate photo to sales@sixwinds.com.sa, or use the RFQ form.

This guide is general information. Final selection must follow the project design, the applicable standards and the maker's data.