العربية Get a quote

Technical guides

ANFO loading hose: pre-shift inspection, care in Saudi heat and when to replace it

A loading hose wears every time prill passes through it and every time it is dragged over rock. Because its safety depends on its electrical behaviour as well as its strength, a worn hose must be taken out of service before it fails, not after.

By the Six Winds engineering team · Updated

Quick answer

Inspect the hose before every shift for cuts, flat spots, wear through to the inner layer and damage at the couplings; keep it out of direct sun and away from sharp edges; record its certificate and service dates; and replace it when damage is found or at the interval your blasting procedure and the maker set.

Step by step

  1. Look along the whole lengthRun the hose through your hands from the loader to the tip. Look for cuts, gouges, flat or kinked sections and places where the outer layer is worn through.
  2. Check the couplingsCheck the fitting at the loader end is tight, undamaged and keeps the electrical path continuous. Replace cracked clamps and worn fittings.
  3. Check the stripe and markingsThe orange stripe should be visible along the hose. If it is worn away in places, the hose has lost wall thickness there.
  4. Clear the boreBlow out residual prill at the end of each shift so it does not cake inside the hose.
  5. Store it properlyCoil it loosely, keep it out of direct sun and off hot surfaces, and away from oil, fuel and sharp edges.
  6. Record and replaceKeep the certificate and service dates with the loader records, and replace the hose when damage is found or at the set interval.

Why inspection matters more for a loading hose

An ordinary air hose is replaced when it leaks. An ANFO loading hose also has to keep its electrical behaviour: it must drain static and still resist stray current. Wear, cuts and heat damage can change that before the hose leaks, so the visual check before each shift is part of the charging procedure, not housekeeping.

Pre-shift checklist

  • Whole length checked by hand and by eye: no cuts, gouges, flat or kinked sections.
  • No wear through the outer layer; the orange stripe visible along the length.
  • Loader-end coupling tight and undamaged; clamps intact.
  • Loader earth connection in place as the blasting procedure requires.
  • Hose identified as the ANFO loading hose (not an air or water hose picked up by mistake).

Heat, sun and storage in Saudi Arabia

The hose is made for use from -35 °C to +65 °C. Surface magazines, laydown areas and vehicle decks in a Saudi summer can be hotter than the air temperature, so keep coils in the shade or under cover, never on hot steel plate, and away from oil and fuel. Coil the hose loosely in large loops; tight coils and sharp bends leave kinks that become flat spots.

Handling on the face

  • Do not drag the hose over sharp rock edges or let machines run over it.
  • Feed the hose into the hole; do not force it past an obstruction.
  • Do not pull the hose by the coupling; pull by the hose near the loader.
  • At the end of the shift blow out residual prill and coil the hose for storage.

When to replace the hose

Replace the hose when you find any cut or gouge into the wall, wear through to the inner layer, flat or crushed sections that do not recover, damage at the couplings, or heat or chemical damage; and in any case at the interval your blasting procedure and the maker set. Do not repair a loading hose with tape or a splice unless the maker and your procedure allow it. Keep a spare coil on site so charging does not stop.

Records for the safety file

For each hose keep the size, coil number or date received, the test certificate, the date it entered service and the inspection notes. When we supply the hose we can include the maker's test certificate and a certificate of origin with the delivery documents; ask for them with your request for quotation.

What to send us for a quotation

The bore size, length per coil and number of coils, any couplings or clamps you need, the delivery site and the documents required. See the ANFO explosive loading hose page or e-mail sales@sixwinds.com.sa.

Common questions

How often should an ANFO loading hose be inspected?

Before every shift, by eye and by hand along the whole length, plus any periodic test your blasting procedure requires.

Can a cut loading hose be taped?

No, unless the maker and your procedure allow a specific repair. A taped hose cannot be relied on mechanically or electrically; replace it.

Does Saudi summer heat damage the hose?

The hose is made for use up to +65 °C, but surfaces in direct sun can be hotter than the air. Store coils in the shade or under cover and off hot steel.

How long does a loading hose last?

It depends on how many holes it charges, the rock and the handling. Replace it when inspection finds damage or at the interval set by your procedure and the maker.

Can you supply the test certificate?

Yes. The maker's test certificate and a certificate of origin can be supplied with the order; ask for them with your request for quotation.

Need these items? E-mail your list or a nameplate photo to sales@sixwinds.com.sa, or use the RFQ form.

This guide is general information. Final selection must follow the project design, the applicable standards and the maker's data.